This is a pre-order. Units will ship by mid-November 2025.
These allow you to mount the most popular Go Kart rims directly to 95% of esk8 drivetrains/trucks!
NO buying new trucks
NO buying new hangers
NO buying a new drivetrain
You can buy a set of slick Vega Go Kart Rims and Tires here:
Rims:
https://www.tsracing.com/Wheels/Douglas-5-Diameter-1-Piece-Wheels/Douglas-50-x-20-x-30-Wheel-Black
Tires:
https://www.tsracing.com/Tires-Prep-and-Tools/Tires-and-Tire-Tools/Vega-QMA-Tires/Vega-XAS-Yellow-10-x-460-5-Left-Rear-Tires
Compatibility list:
Bearing spacing:
MBS - with extended outside bearing bores, you can stack up to three bearings for increased load capacity, depending how much axle space you have. We worked closely with Big Bearing™ on this design to ensure you’ll be buying as many bearings as possible.
Urethane (please don’t actually use this, it was put there exclusively for shits, giggles, and photo shoots) - one 22mm bearing seat, one 28mm bearing seat. Use one 608 and one 638 bearing
Esk8 drive bolt patterns:
MBS - threaded holes
China 80mm - threaded holes; MBS usually works fine but we added it just in case
Linnpower/Etoxx gear drives - 40mm circle
Exway gear drives - 43mm circle
SRB drive hub pattern, but M4 instead of 8-32 (in case the MBS interface suddenly disappears again )
Additional patterns might be added on a case by case basis if you ask within the next few days, but no guarantees
Go kart wheel bolt patterns:
American standard - uses captive nut pockets on the inside of the hub and bolts to attach the wheel. These hubs have been tested to fit inside DWT Classic American standard wheels, which is what Stooge has been using
Metric standard - counterbored threaded holes to accept standard M8x1.25 kart studs
CRG front hub standard - counterbored threaded holes to accept standard M8x1.25 kart studs
These hubs are designed for kart wheels with 2” backspacing or less. Others might work, but likely future batches of these made at different lengths will be required.
This is a pre-order. Units will ship by mid-November 2025.
These allow you to mount the most popular Go Kart rims directly to 95% of esk8 drivetrains/trucks!
NO buying new trucks
NO buying new hangers
NO buying a new drivetrain
You can buy a set of slick Vega Go Kart Rims and Tires here:
Rims:
https://www.tsracing.com/Wheels/Douglas-5-Diameter-1-Piece-Wheels/Douglas-50-x-20-x-30-Wheel-Black
Tires:
https://www.tsracing.com/Tires-Prep-and-Tools/Tires-and-Tire-Tools/Vega-QMA-Tires/Vega-XAS-Yellow-10-x-460-5-Left-Rear-Tires
Compatibility list:
Bearing spacing:
MBS - with extended outside bearing bores, you can stack up to three bearings for increased load capacity, depending how much axle space you have. We worked closely with Big Bearing™ on this design to ensure you’ll be buying as many bearings as possible.
Urethane (please don’t actually use this, it was put there exclusively for shits, giggles, and photo shoots) - one 22mm bearing seat, one 28mm bearing seat. Use one 608 and one 638 bearing
Esk8 drive bolt patterns:
MBS - threaded holes
China 80mm - threaded holes; MBS usually works fine but we added it just in case
Linnpower/Etoxx gear drives - 40mm circle
Exway gear drives - 43mm circle
SRB drive hub pattern, but M4 instead of 8-32 (in case the MBS interface suddenly disappears again )
Additional patterns might be added on a case by case basis if you ask within the next few days, but no guarantees
Go kart wheel bolt patterns:
American standard - uses captive nut pockets on the inside of the hub and bolts to attach the wheel. These hubs have been tested to fit inside DWT Classic American standard wheels, which is what Stooge has been using
Metric standard - counterbored threaded holes to accept standard M8x1.25 kart studs
CRG front hub standard - counterbored threaded holes to accept standard M8x1.25 kart studs
These hubs are designed for kart wheels with 2” backspacing or less. Others might work, but likely future batches of these made at different lengths will be required.
